Are you searching for advice concerning Tools You Need to Install a New Bathtub ?
Mounting a bath tub isn't specifically rocket science, yet it does require solid plumbing, carpentry, and in some cases, tiling skills. Replacing an old bathtub with a new one is likewise a moderately challenging project. If the old tub is easily easily accessible, the job can relocate easily; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need a helper to leave the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to hiring a professional to take over a halfway-completed project, it is better to consider using one prior to you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will assist you set up a brand-new tub in your washroom if you have actually currently acquired a new tub and don't require to transform the setup of your previous water system pipes.
Your tools and also product list must make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted accessibility that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single faucets from transforming during this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the new faucets, compare the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin guaranteeing that the washing machines remain in location in between the tap and also the sink. Protect the faucet in place with the supplier offered backnut. As soon as the tap is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap adapters. The former type needs to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Making use of both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub until the spirit level checks out degree.
To mount taps, fit the bottom of the furthest adaptable faucet connector to the suitable supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the water system and also examine all joints and also new pipework for leaks and tighten them if required. Fill up the tub as well as additionally examine the overflow outlet and the normal outlet for leaks.
Lastly, repair the bath paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Planning for the Installment
To start with, the sustaining framework provided with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to prevent strain on the bath tub.
Fit the adaptable tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Ensure you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should currently be ready to be suited its final position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, resulting in difficulties with moisture and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water prior to sealing, to enable the activity experienced when the tub remains in usage. The sealant can break rather early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily offered on the marketplace. It is suggested to fit the tiles utilizing water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading about A Step-by-Step Guide to Installing a Bathtub? Create a review further down. We would be delighted to listen to your feelings about this content. In hopes that you come back again in the future. Sharing is nice. You never know, you may just be doing someone a favor. Thank you for your time. Please pay a visit to our blog back soon.
Prices & Booking